Everything about Wire totally explained
A
wire is a single, usually
cylindrical, elongated string of
drawn metal. Wires are used to bear mechanical
loads and to carry
electricity and
telecommunications .
Standard sizes are determined by various
wire gauges. The term
wire is also used more loosely to refer to a bundle of such strands, as in 'multistranded wire', which is more correctly termed a
cable.
History
In
antiquity,
jewellery often contains, in the form of chains and applied decoration, large amounts of wire that's accurately made and which must have been produced by some efficient, if not technically advanced, means. In some cases, strips cut from metal sheet were made by pulling them through perforations in stone beads. This causes the strips to fold round on themselves to form thin tubes. This strip drawing technique was in use in
Egypt by the
2nd Dynasty. From the middle of the
2nd millennium BC most of the
gold wires in jewellery are characterized by seam lines that follow a spiral path along the wire. Such twisted strips can be converted into solid round wires by rolling them between flat surfaces or the strip wire drawing method. Strip and block twist wire manufacturing methods were still in use in
Europe in the
7th century AD, but by this time there seems to be some evidence of wires produced by true
drawing.
Square and hexagonal wires were possibly made using a swaging technique. In this method a metal rod was struck between grooved metal blocks, or between a grooved punch and a grooved metal anvil. Swaging is of great antiquity, possibly dating to the beginning of the 2nd millennium BC in Egypt and in the
Bronze and
Iron Ages in Europe for
torches and
fibulae.
Twisted square section wires are a very common
filigree decoration in early
Etruscan jewellery.
In about the middle of the 2nd millennium BC a new category of decorative wires was introduced which imitated a line of granules. Perhaps the earliest such wire is the notched wire which first occurs from the late
3rd, early 2nd millennium BC in
Anatolia and occasionally later.
Wire was
drawn in England from the medieval period. The wire was used to make wool cards and pins, manufactured goods whose import was prohibited by
Edward IV in 1463. The first wire mill in
Great Britain was established at
Tintern in about
1568 by the founders of the
Company of Mineral and Battery Works, who had a
monopoly on this. Apart from their second wire mill at nearby Whitebrook, there were no other wire mills before the second half of the
17th century. Despite the existence of mills, the drawing of wire down to fine sizes continued to be done manually.
Wire is usually drawn of cylindrical form; but it may be made of any desired section by varying the outline of the holes in the draw-plate through which it's passed in the process of manufacture. The
draw-plate or
die is a piece of hard cast-iron or hard steel, or for fine work it may be a
diamond or a
ruby. The object of utilizing precious stones is to enable the dies to be used for a considerable period without losing their size, and so producing wire of incorrect diameter. Diamond dies must be rebored when they've lost their original diameter of hole, but the metal dies are brought down to size again by hammering up the hole and then drifting it out to correct diameter with a punch.
Uses
Wire has many uses. It forms the raw material of many important
manufacturers, such as the wire-net industry, wire-cloth making and wire-
rope spinning, in which it occupies a place analogous to a
textile fiber. Wire-
cloth of all degrees of strength and fineness of mesh is used for sifting and screening machinery, for draining
paper pulp, for window screens, and for many other purposes. Vast quantities of
aluminum,
copper,
nickel and
steel wire are employed for telephone and data wires and cables, and as conductors in
electric power transmission, and heating. It is in no less demand for fencing, and much is consumed in the construction of suspension bridges, and cages, etc. In the manufacture of stringed musical instruments and scientific instruments wire is again largely used. Among its other sources of consumption it's sufficient to mention pin and hair-pin making, the needle and fish-hook industries, nail, peg and rivet making, and carding machinery; indeed there are few industries into which it doesn't enter.
Not all metals and metallic
alloys possess the physical properties necessary to make useful wire. The metals must in the first place be
ductile and strong in tension, the quality on which the utility of wire principally depends. The metals suitable for wire, possessing almost equal ductility, are
platinum,
silver,
iron,
copper,
aluminum and
gold; and it's only from these and certain of their
alloys with other metals, principally
brass and
bronze, that wire is prepared. By careful treatment extremely thin wire can be produced. Special purpose wire is however made from other metals (for example
tungsten wire for
light bulb and
vacuum tube filaments, because of its high melting temperature).
Production
Wire is often reduced to the desired diameter and properties by repeated drawing through progressively smaller dies, or traditionally holes in
draw plates. The wire may be heated to red heat in an inert atmosphere to soften it, and then cooled, in a process called
annealing. An inert atmosphere is used to prevent oxidation, although some scaling always occurs and must be removed by 'pickling' before the wire is redrawn.
An important point in wire-drawing is that of lubrication to facilitate the operation and to lessen the wear on the dies. Various lubricants, such as
oil, are employed. Another lubrication method is to immerse the wire in a
copper (II) sulfate solution, such that a film of copper is deposited which forms a kind of lubricant; this eases the wire-drawing considerably. In some classes of wire the copper is left after the final drawing to serve as a preventive of
rust or to allow easy
soldering.
The wire-drawing machines include means for holding the dies accurately in position and for drawing the wire steadily through the holes. The usual design consists of a cast-iron bench or table having a bracket standing up to hold the die, and a vertical drum which rotates and by coiling the wire around its surface pulls it through the die, the coil of wire being stored upon another drum or "swift" which lies behind the die and reels off the wire as fast as required. The wire drum or "block" is provided with means for rapidly coupling or uncoupling it to its vertical shaft, so that the motion of the wire may be stopped or started instantly. The block is also tapered, so that the coil of wire may be easily slipped off upwards when finished. Before the wire can be attached to the block, a sufficient length of it must be pulled through the die; this is effected by a pair of gripping pincers on the end of a chain which is wound around a revolving drum, so drawing the pincers along, and with them the wire, until enough is through the die to be coiled two or three times on the block, where the end is secured by a small screw clamp or vice ready for the drawing operation. Wire has to be pointed or made smaller in diameter at the end before it can be passed through the die; the pointing is done by hammering, filing, rolling or swaging in dies, which effect a reduction in diameter. When the wire is on the block the latter is set in motion and the wire is drawn steadily through the die; it's very important that the block shall rotate evenly and that it'll run true and pull the wire in an even manner, otherwise the "snatching" which occurs will break the wire, or at least weaken it in spots.
Continuous wire-drawing machines differ from the single-block machines in having a series of dies through which the wire passes in a continuous manner. The difficulty of feeding between each die is solved by introducing a block between each, so that as the wire issues it coils around the block and is so helped on to the next die. The speeds of the blocks are increased successively, so that the elongation due to drawing is taken up and slip compensated for. The operation of threading the wire first through all the dies and around the blocks is termed "stringing-up." The arrangements for lubrication include a pump which floods the dies, and in many cases also the bottom portions of the blocks run in lubricant. The speeds at which the wire travels vary greatly, according to the material and the amount of reduction effected.
Finishing, jacketing, and insulating
Electrical wires are covered with various insulating materials, such as plastic or rubber-like polymers. Two or more insulated wires are wrapped concentrically and further protected with substances like paraffin, some kind of preservative compound, bitumen or lead sheathing or steel taping. Stranding or covering machines wind material onto the wire, which passes through quickly. Some of the smallest machines for cotton covering have a large drum, which grips the wire and moves it through toothed gears; the wire passes through the centre of disks mounted above a long bed, and the disks carry each a number of bobbins varying from six to twelve or more in different machines. A supply of covering material is wound on each bobbin, and the end is led on to the wire, which occupies a central position relatively to the bobbins; the latter being revolved at a suitable speed bodily with their disks, the cotton is consequently served on to the wire, winding in spiral fashion so as to overlap. If a large number of strands are required the disks are duplicated, so that as many as sixty spools may be carried, the second set of strands being laid over the first.
For the heavier cables, used for
electric light and power, and submarine cables, the machines are somewhat different in construction. The wire is still carried through a hollow shaft, but the bobbins or spools of covering material are set with their spindles at right angles to the axis of the wire, and they lie in a circular cage which rotates on rollers below. The various strands coming from the spools at various parts of the circumference of the cage all lead to a disk at the end of the hollow shaft. This disk has perforations through which each of the strands pass, thence being immediately wrapped on the cable, which slides through a bearing at this point. Toothed gears having certain definite ratios are used to cause the winding drum for the cable and the cage for the spools to rotate at suitable relative speeds which don't vary. The cages are multiplied for stranding with a large number of tapes or strands, so that a machine may have six bobbins on one cage and twelve on the other.
Insulating and jacketing of wires and cables is done by passing them through an extruder. Since the mid-
1960s, the insulation has been plastic or polymers exhibiting properties similar to rubber.
Types of wire
Solid
Solid wire or solid-core wire consists of one piece of metal wire. Solid single strand wire is cheaper to manufacture than stranded wire and is used where there's no need for flexibility in the wire. Solid wire also provides strength and protection against the environment.
Stranded
Stranded wire is composed of a bundle of small-gauge wires to make a larger conductor, which may optionally be insulated. Stranded wire is more flexible than a solid strand of the same total gauge. Stranded conductors are commonly used for electrical applications carrying small signals, such as computer mouse cables, and for power cables between a movable appliance and its power source; for example, sweepers, table lamps, powered hand tools, welding electrode cables, mining machines and trailing machine cables.
At high frequencies, current travels near the surface of the wire because of the
skin effect, resulting in increased power loss in the wire. Stranded wire might seem to reduce this effect, since the total surface area of the strands is greater than the surface area of the equivalent solid wire, but in fact a simple stranded wire will have worse skin effect than a solid wire, because of its increased average resistivity due to inclusion of air gaps within the wire.
However, for many high-frequency applications,
proximity effect is more severe than
skin effect, and in some limited cases, simple stranded wire can reduce proximity effect. For better performance at high frequencies,
litz wire, which has the individual strands insulated and twisted in special patterns, can be used.
Further Information
Get more info on 'Wire'.
|
External Link Exchanges
Do you know how hard it is to get a link from a large encyclopaedia? Well we're different and will prove it. To get a link from us just add the following HTML to your site on a relevant page:
<a href="http://wire.totallyexplained.com">Wire Totally Explained</a>
Then simply click through this link from your web page. Our crawlers will verify your link, extract the title of your web page and instantly add a link back to it. If you like you can remove the words Totally Explained and embed the link in article text.
As long as your link remains in place, we'll keep our link to you right here. Please play fair - our crawlers are watching. Your site must be closely related to this one's topic. Any kind of spamming, dubious practises or removing the link will result in your link from us being dropped and, potentially, your whole site being banned. |
